Fix Victony WiFi Extender Keeps Disconnecting Issue

Are you getting an issue with your Victony WiFi extender as it keeps on disconnecting? If yes, then need not to worry. Here, we have arrived with some effective troubleshooting methods through which you can easily fix the Victony WiFi extender keeps disconnecting issue.

Reasons: WiFi Extender Keeps Disconnecting Issue

Here are some common reasons for getting the WiFi repeat keeps disconnecting issue. Just have a quick view.

• Improper placement of WiFi extender
• Using the old version of extender firmware
• Partial or incorrect Victony WiFi extender setup
• Poor internet connection
• Unstable power supply
• WiFi interference

Resolved: Victony Extender Keeps Disconnecting Issue

Reboot Your Extender

In some cases, users might come also across the Victony WiFi extender keeps disconnecting issue due to minor technical hitches. These hitches can be fixed by simply performing a reboot of your device. Apart from fixing the minor technical glitches, it also prevents your extender from getting overheated. So, without any delay, let’s begin with rebooting your device by following the below-mentioned steps.

• Then, get the extender off the electric source and turn it off.
• Now, wait for a while prior to connecting your Victony WiFi extender to the power socket and turn it on.

After executing the aforementioned steps, see if the WiFi extender keeps disconnecting issue has been fixed.

Inspect the Ethernet Connection

You are required to confirm that the Ethernet cable you’re using to connect your Victony WiFi extender and the router don’t have any cuts. Replace the older Ethernet wire with a new one in case you find any wear or tear on the cable you are using. Moreover, you need to ensure that the Ethernet connection between your devices should be finger-tight for smooth functioning.

Check the Power Supply

Ensure that the power socket through which your Victony WiFi extender is connected is in good working condition. Any damage or short-circuit in the power socket can lead you to face the Victony WiFi extender keeps disconnecting issue. In that case, try switching your extender to another power socket.

Place at an Optimal Location

You need to be very cautious while selecting the place of your Victony WiFi extender as it needs to be placed within the range of your router. Avoid placing your extender close to reflexive surfaces and water bodies as it can degrade the performance of the WiFi signals.

Here we have mentioned a few things which you need to keep in mind for optimal results.

• Avoid objects such as refrigerators, microwaves, baby monitors, Bluetooth devices, and other smart home appliances to prevent interference in the WiFi signals.
• Place your extender at the central location of your house.

For more information, get in touch with our experts for instant support.

Update Victony Extender Firmware

Make sure that the firmware version of the Victony WiFi extender you’re accessing is up-to-date. If that’s not the case, then you might get stuck with the Victony WiFi extender keeps disconnecting issue. Therefore, consider upgrading the firmware of the extender to the most recent version.

Change WiFi Channel

Accessing an overcrowded channel can also be one of the reasons why your Victony WiFi extender keeps disconnecting. In that case, try jumping to another WiFi channel with the minimum crowd. You can check the traffic of the WiFi channel by visiting the extender setup page.

Perform Factory Default Reset

If all your efforts went in vain and you still aren’t able to fix the Victony WiFi extender keeps disconnecting issue, then, consider resetting your Victony extender to the default factory settings and configure it again from the basics. This will eliminate all types of minor or major issues spoiling your internet experience. However, it’s not a hard task, but still many users find it a little bit complex. If you are also the one getting a hard time, then go through the instructions mentioned below to perform the default factory reset of your Victony WiFi extender.

• Firstly, you should locate the Reset button on your extender.
• Then, push the button once you have located the Reset button.
• Thereafter, your Victony WiFi extender will reboot on its own and is restored.

Once your extender is restored to the default factory settings, you can now configure it to access high-speed internet.

So, this is all about how you can resolve the Victony WiFi extender keeps disconnecting issue with ease. If you have any queries such as how to setup Victony extender, how to recover the admin password, or any other similar kind of queries, then don’t hesitate to contact our IT professionals.