Uncut Guide to Setup Victony 1200Mbps WiFi Signal Booster
In this guide, we have talked about two different methods through which configuring the Victony 1200Mbps WiFi signal booster is possible. The first method requires you to press the WPS button and the other method needs you to access the web user interface of your device. To know in detail how to configure your device using both these methods, walk through this blog without wasting any more time.
Setup Victony 1200Mbps WiFi Signal Booster: WPS Method
Here are the instructions using which you can install the 1200Mbps WiFi signal booster using the WPS or the WiFi Protected Setup method:
- Locate a wall socket in your house.
- Plug the Victony 1200Mbps WiFi signal booster into it.
- Hit the power button.
- Hold on for some time.
- Thereafter, hit the WPS button on the booster as well as the host router.
- Relocate your booster.
Before you even know it, you will be able to configure the Victony 1200Mbps WiFi signal booster. Now, you are free to access the internet in every corner of your house.
Setup Victony 1200Mbps WiFi Signal Booster: Manual Method
Do you have the default admin login password and username of your Victony 1200Mbps WiFi signal booster with you right now? Good. Because you will need them.
Follow these guidelines in order to configure your booster using the manual method:
- First of all, physically set up your Victony booster, just like you did above.
- Then, connect the booster to the router.
- That can be done with the help of a wired source of connection.
- Switch on your laptop.
- Open an internet browser, and that too an updated one.
- In the address bar or the URL field, type the default web address.
- Hit Enter.
- Once you have accessed the login page, enter the password and username.
- Click on Login.
- As soon as the Victony extender setupwizard, go through the on-screen prompts.
And with that, you will be able to complete setting up the Victony 1200Mbps WiFi signal booster using the manual method. In case, you face issues at any point, the below-given steps will help you to get rid of them.
Can’t Setup Victony 1200Mbps WiFi Signal Booster?
1. Proper Power Supply
First of all, check if you have connected your Victony 1200Mbps WiFi signal booster to a working wall socket or not. In case not, then it is quite obvious why you are experiencing the setup issues. To troubleshoot them, it is recommended that your wireless range extender is into a different but working wall socket.
After following this hack, check if you are able to configure the Victony 1200Mbps WiFi signal booster without any issues this time. In case, you are still not able to, then take our advice and take your attention to the next hack. Perhaps, the first hack could not help; the second one might give you a different result.
2. Stable Ethernet Connection
Using a damaged Ethernet cable to connect the Victony 1200Mbps WiFi signal booster and the host router can also cause setup issues. Therefore, you have two options in hand. The first one requires you to tape up your existing Ethernet cable and the other one requires you to bring a new Ethernet cable home.In case you decide to bring a new Ethernet cable home, then connect one end to the extender and another to the host router. Once done, ensure that the cable connection between both networking devices is finger-tight. Otherwise, your devices will not be able to transmit signals in a happy-go-lucky way.
3. Correct Login Credentials
Did you not check the login password and username before clicking on the Login button? No? Well, it looks like you found another factor that might have contributed to the setup issues. To troubleshoot them, it is recommended that type the login credentials of your Victony 1200Mbps WiFi signal booster again into their respective fields.
In case you are not sure about them, then why don’t you take your attention to the user manual that you got with your wireless range extender? Starting from the default web address to the default login credentials, this little book has everything that you need to know about your Victony extender.
The Bottom Line
This was all about how you can setup Victony 1200Mbps WiFi signal booster using the WPS method as well as the Manual method. Although you will be able to walk through the setup process with the help of the guide, in case you are not able to, then getting in touch with our technical experts will serve you well. If you do not want to do that, then it is advised that you perform Victony WiFi extender reset and then set up your device from scratch.