Victony WiFi Extender Not Connecting to Router – Simple Hacks
If you want to make the most of your range extender, you are required to pair it with the router properly. However, things won’t turn in your favor if the connection fails. Well, this post is all about that. Here, we’ve targeted this problem in relation to a Victony extender. Therefore, let’s start the troubleshooting guide to fix the Victony WiFi extender not connecting to router issue.
Know that pairing of both devices is necessary as it may not only stop you from managing the home network but it also tends to halt the Victony extender setup process. Now, move to the next section to understand what might have caused the problem.
Note: Your Victony extender is supposed to be receiving a constant power supply. Any fluctuation in power can result in other problems.
Victony WiFi Extender Not Connecting to Router – Reasons
A plethora of reasons is there why you can’t connect your WiFi range extender with the main router. But, the major cause is the improper extender-router distance. Chances are that you’ve placed your WiFi devices too far due to which they are facing problems communicating with each other. Thus, try reducing the distance between your WiFi devices first.
Does it bear any fruit? No? Perhaps, you brought them too close this time. If you’ve done so, then place them a little apart. Know that making this distance zero can result in a clash of WiFi signals of both devices. To know more about the extender-router distance, checking out the extender’s user manual is recommended. From how to reset Victony WiFi extender to set it up again, every detail is mentioned in it. However, if you are still facing problems, walk through the points given below to understand other reasons causing them.
1. Damaged Cable
To get success with the connection process, a user is required to couple the router and extender using an Ethernet cable. Chances are that one used by you is either damaged or the connection created by you is shaky.
2. Signal Interference
If your WiFi range extender sits at a place where its signals are getting interrupted, then also the Victony WiFi extender not connecting to router problem can show up. How can you expect a device to pair with another one if it cannot transmit signals?
So, these were the reasons due to which your Victony extender might refuse to connect to the router. But, no matter what the reason is, walking through the hacks mentioned in the following section will help you out.
Victony WiFi Extender Not Connecting to Router – Fixes
Before doing anything else, consider restarting the range extender. Perhaps, a glitch is affecting its ability to pair up with the router. In order to do that, you are required to disconnect the extender from the power outlet and wait for a few moments. Thence, recreate the power connection and switch on your WiFi device. If it fails to resolve the problem, follow the given hacks.
1. Change the Ethernet Cable
Have a good look at the Ethernet cable that has been given the job of pairing your WiFi devices directly. If it is all well, then OK. Otherwise, replace it with a new one immediately. However, changing the cable won’t bring you any luck if the connection created by you is not finger-tight. Therefore, be sure about the same. And yes, do cross-check the working status of the Ethernet ports of your WiFi devices before concluding anything.
2. Remove Signal Interference
Another Victony extender troubleshooting tip you can follow to get rid of the situation you are currently in is the relocation of the extender. Sometimes, the location of the extender is not right. In that case, you are advised to relocate it and prevent its signals from getting diverted or blocked. However, you should not place it under a table or inside a cupboard. Proper ventilation of the extender’s location is necessary.
In a Nutshell
This was all about what to do if the Victony WiFi extender not connecting to router situation shows up. Here, you learned that the improper router-extender distance, a damaged Ethernet cable, or signal interference are the major culprits behind the problem.
You also learned about the ways to tackle the problem effectively. Now, we assume that you have successfully addressed the issue and are having a marvelous experience with your WiFi device.
However, we do not want you to face the same issue in the future. Therefore, consider upgrading the firmware of your Victony range extender to the latest version. The reason being it controls all the hardware and software activities carried out by the range extender. But, be very sure about the file you upload during the firmware update process. Else, your extender may get bricked.